Kelco Catalogue

Modelos enKelco Catalogue Catalog
Resultados 1-8 de 8
< Página anterior1Página siguiente >
Resultados por página:
Número de pieza
Proveedor
Descripción
The L Series side entry level switch provides a reliable accurate and low cost solution to tank level control. Theswitch is available in all thermoplastic construction or in a combination of 316 Stainless Steel and Polypropylene.The level switch can be supplied with a 500 Volt rated single pole double throw micro switch for general controlcircuit use or with a S.P.D.T reed switch for low voltage low current applications. The L Series level switch isbuilt tough to give a long reliable service life in the most arduous applications.
¿Configuraciones?
No
Descargas
21
Agregado el
14 dic., 2016
Número de pieza
Proveedor
Descripción
The P25 inline flow switch is a rugged versatile all position mounting flow actuated switch that can detect the flow of liquids in 15mm (1/2”) to 25mm (1”) diameter pipes. The P25 can be used in larger pipe systems provided the maximum flow does not exceed 100 litres per minute. The switch can detect very low flows and yet has a low head loss high flow through rating. It can be used to detect continuous or pulsed flows.
¿Configuraciones?
No
Descargas
10
Agregado el
19 jun., 2016
Número de pieza
Proveedor
Descripción
The P25 inline flow switch is a rugged versatile all position mounting flow actuated switch that can detect the flow of liquids in 15mm (1/2”) to 25mm (1”) diameter pipes. The P25 can be used in larger pipe systems provided the maximum flow does not exceed 100 litres per minute. The switch can detect very low flows and yet has a low head loss high flow through rating. It can be used to detect continuous or pulsed flows.
¿Configuraciones?
No
Descargas
8
Agregado el
19 jun., 2016
Número de pieza
Proveedor
Descripción
The P25 inline flow switch is a rugged versatile all position mounting flow actuated switch that can detect the flow of liquids in 15mm (1/2”) to 25mm (1”) diameter pipes. The P25 can be used in larger pipe systems provided the maximum flow does not exceed 100 litres per minute. The switch can detect very low flows and yet has a low head loss high flow through rating. It can be used to detect continuous or pulsed flows.
¿Configuraciones?
No
Descargas
17
Agregado el
19 jun., 2016
Número de pieza
Proveedor
Descripción
Advanced Pump Controller
¿Configuraciones?
No
Descargas
13
Agregado el
25 may., 2016
Número de pieza
Proveedor
Descripción
The F Series flow switch is a tough but highly sensitive paddle flow switch suitable for a wide range of flow control applications in both hot and cold liquids. The electrical housing of the switch is a separate assembly and locks onto the wet end of the switch. It can be easily and safely removed for servicing, without disturbing electrical wiring. This unique feature, and the inclusion of a built in manual override make the F Series a very versatile flow switch. In addition to the standard microswitch models the F Series is available fitted with reed switches for PLC, relay logic and telemetry applications
¿Configuraciones?
No
Descargas
63
Agregado el
17 may., 2016
Proveedor
Descripción
The D30 two position top entry level switch operates on the principle of displacement. When non floating solid polypropylene displacers, suspended from the switch, are immersed in liquid their weight is reduced by an amount equal to the weight of the liquid they displace, This weight change is detected and used to actuate a magnetically isolated switch. Surface agitation, froth, floating or submerged solids do not effect the action of the D30 switch. The displacement principle depends on the specific gravity of the liquid in which the displacers are suspended. The switch is set to operate in water, at a specific gravity of 1+/- 5%.
¿Configuraciones?
No
Descargas
21
Agregado el
24 may., 2016
Proveedor
Descripción
The D30 two position top entry level switch operates on the principle of displacement. When non floating solid polypropylene displacers, suspended from the switch, are immersed in liquid their weight is reduced by an amount equal to the weight of the liquid they displace, This weight change is detected and used to actuate a magnetically isolated switch. Surface agitation, froth, floating or submerged solids do not effect the action of the D30 switch. The displacement principle depends on the specific gravity of the liquid in which the displacers are suspended. The switch is set to operate in water, at a specific gravity of 1+/- 5%.
¿Configuraciones?
No
Descargas
5
Agregado el
24 may., 2016

Acerca de

Established in 1974, Kelco Engineering operates from two large well equipped factories in Brookvale, Sydney Australia. Our facility consists of a modern toolroom equipped with the latest CNC machinery, for die and mould production. In addition we operate comprehensive manufacturing, including in hou...
Más...

Información del contacto

Dirección:
9 / 9 Powells Road
Brookvale, 2100
New South Wales, Australia
Teléfono: +61299056425
Fax: +61299056420
Correo electrónico:
Sitio Web: http://www.kelco.com.au/m...